Warning:
JavaScript is turned OFF. None of the links on this page will work until it is reactivated.
If you need help turning JavaScript On, click here.
The Concept Map you are trying to access has information related to:
Exact length of the voltage will be... Held for each bit, Receivers cannot mark the start and end of bits furthermore the sender must... Leave the line idle for a set time (Considered the minimum time), RS-232C (view mouse over info) also introduces... Baud Rate, RS-232C (view mouse over info) also introduces... Framing Errors, RS-232C (view mouse over info) specifies phsyical connections... Less than 50ft Connection, RS-232C (view mouse over info) specifies phsyical connections... Specifies transmission of Characters, RS-232C (view mouse over info) specifies phsyical connections... Voltage data range (-15 volts to +15 volts), Full Duplex Transmission (view mouse over info) requires 3 wires... A ground, Full Duplex Transmission (view mouse over info) requires 3 wires... Data traveling in reverse direction, Full Duplex Transmission (view mouse over info) requires 3 wires... Data to travel in one direction, Transmission Synchronization (Not Required) a standard created by Elictronic Industries Association (EIA) RS-232C (view mouse over info), RS-232C (view mouse over info) furthermore defines... Serial Asynchronous Communication (view mouse over info), Second is the Ground used to perform several directional transfers... Full Duplex Transmission (view mouse over info), Second is the Ground used to perform several directional transfers... Half Duplex Transmission (view mouse over info), Second is the Ground used to perform several directional transfers... Simplex Transmission (view mouse over info), POSITIVE (Represented by a voltage of 0) SPACE STATE when transmitter has nothing to send... Wire is set at negative voltage (Corresponds to bit value 1), Serial Asynchronous Communication (view mouse over info) communication is transferred through 2 twisted wires... One carries the signal, Serial Asynchronous Communication (view mouse over info) communication is transferred through 2 twisted wires... Second is the Ground, Time required to send 1 bit the stop bit is called... Phantom Bit, Exact time of the voltage will be... Held for each bit, One carries the signal used to perform several directional transfers... Full Duplex Transmission (view mouse over info), One carries the signal used to perform several directional transfers... Half Duplex Transmission (view mouse over info), One carries the signal used to perform several directional transfers... Simplex Transmission (view mouse over info), Transmission Synchronization (Not Required) this is possible by using... Electrical Current to Send Bits, Receiver must agree on... Exact length, Receiver must agree on... Exact time, Electrical Current to Send Bits sends two types of bits POSITIVE (Represented by a voltage of 0) SPACE STATE, Electrical Current to Send Bits sends two types of bits NEGATIVE (Represented by a voltage of 1) MARK STATE, Local Asynchronous Communication (RS-232) sender and receiver... Transmission Synchronization (Not Required), NEGATIVE (Represented by a voltage of 1) MARK STATE when transmitter has nothing to send... Wire is set at negative voltage (Corresponds to bit value 1), Wire is set at negative voltage (Corresponds to bit value 1) because wires can not be set to 0 between each bit... Receivers cannot mark the start and end of bits, Receivers cannot mark the start and end of bits instead both the.... Receiver, Receivers cannot mark the start and end of bits instead both the.... Sender, Specifies transmission of Characters is able to transmit... 8 bit characters (Capable of supporting), Specifies transmission of Characters is able to transmit... 7 bit characters (Configured at this level), Framing Errors occurs if... If the stop bit occurs unexpectantly, Framing Errors occurs if... Voltage does not agree, Framing Errors occurs if... Baud Rates are not properly configured, Leave the line idle for a set time (Considered the minimum time) this time is considered... Time required to send 1 bit, Baud Rate which is... Changes in signal per second, Sender must agree on... Exact length, Sender must agree on... Exact time